View 1516BQ_1396106.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

d a t a sh eet product speci?cation file under integrated circuits, ic01 july 1994 integrated circuits tda1516BQ 24 w btl or 2 x 12 watt stereo car radio power amplifier
july 1994 2 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ general description the tda 1516BQ is an integrated class-b output amplifier in a 13-lead single-in-line (sll) plastic power package. the device is primarily developed for car radio applications. features requires very few external components flexibility in use - stereo as well as mono btl high output power (without bootstrap) low offset voltage at output (important for btl) fixed gain good ripple rejection mute/stand-by switch load dump protection a.c. and d.c. short-circuit-safe to ground and v p thermally protected reverse polarity safe capability to handle high energy on outputs (v p = 0 v) no switch-on/switch-off plop flexible leads low thermal resistance identical inputs (inverting and non-inverting) compatible with tda1518q (except gain) quick reference data parameter conditions symbol min. typ. max. unit supply voltage range operating v p 6,0 14,4 18,0 v non-operating v p -- 30,0 v load dump protected v p -- 45,0 v repetitive peak output current i orm -- 4a total quiescent current i tot - 30 - ma stand-by current i sb - 0,1 100 m a switch-on current i sw -- 40 m a input impedance btl |z i |25 -- k w stereo |z i |50 -- k w stereo application output power thd = 10%; 4 w p o - 6 - w thd = 10%; 2 w p o - 11 - w channel separation a 40 -- db noise output voltage v no(rms) - 50 -m v btl application output power thd = 10%; 4 w p o - 22 - w supply voltage r s = 0 w ; ripple rejection f = 100 hz to 10 khz rr 48 -- db d.c. output offset voltage | d v o | -- 100 mv
july 1994 3 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ package outline 13-lead sil-bent-to-dil; plastic power (sot141); sot141-6; 1996 july 24. fig.1 block diagram.
july 1994 4 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ pinning functional description the tda1516BQ contains two identical amplifiers with differential input stages. this device can be used for stereo or bridge applications. the gain of each amplifier is fixed at 20 db. a special feature of this device is the mute/stand-by switch which has the following features: low stand-by current (< 100 m a) low mute/stand-by switching current (low cost supply switch) mute condition. ratings limiting values in accordance with the absolute maximum system (iec 134) 1 - inv1 non-inverting input 1 8 bs2 bootstrap 2 2 inv inverting input 9 out2 output 2 3 gnd1 ground (signal) 10 v p supply voltage 4v ref reference voltage 11 m/ss mute/stand-by switch 5 out1 output 1 12 rr supply voltage ripple rejection 6 bs1 bootstrap 1 13 - inv2 non-inverting input 2 7 gnd2 ground (substrate) parameter conditions symbol min. max. unit supply voltage operating v p - 18 v non-operating v p - 30 v load dump protected during 50 ms; t r 3 2,5 ms v p - 45 v a.c. and d.c. short-circuit- safe voltage v psc - 18 v reverse polarity v pr - 6v energy handling capability at outputs v p = 0 v - 200 mj non-repetitive peak output current i osm - 6a repetitive peak output current i orm - 4a total power dissipation see fig.2 p tot - 25 w crystal temperature t c - 150 c storage temperature range t stg - 55 + 150 c
july 1994 5 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ fig.2 power derating curve.
july 1994 6 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ d.c. characteristics (note 1) v p = 14,4 v; t amb = 25 c; unless otherwise speci?ed parameter conditions symbol min. typ. max. unit supply supply voltage range note 2 v p 6,0 14,4 18,0 v quiescent current i p - 40 80 ma d.c. output voltage at approximately v p /2 note 3 v o - 6,8 - v d.c. output offset voltage | d v 5-9 | -- 100 mv mute/stand-by switch switch-on voltage level v on 8,5 -- v mute condition v mute 3,0 - 6,4 v output signal in mute v i = 1 v (max.); position f = 20 hz to 15 khz v o -- 2mv d.c. output offset voltage | d v 5-9 | -- 100 mv stand-by condition v sb 0 - 2v d.c. current in stand-by condition i sb -- 100 m a switch-on current i sw - 12 40 m a
july 1994 7 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ a.c. characteristics v p = 14,4 v; r l = 4 w ; f = 1 khz; t amb = 25 c; unless otherwise speci?ed parameter conditions symbol min. typ. max. unit stereo application note 1 output power note 4; thd = 0,5% p o 45 - w thd = 10% p o 5,5 6,0 - w notes 4 and 5; thd = 10% p o 67 - w output power at note 4; r l = 2 w thd = 0,5% p o 7.5 8,5 - w thd = 10% p o 10 11 - w notes 4 and 5; thd = 10% p o 10,5 12,0 - w low frequency roll-off note 6; - 3 db f l - 45 - hz high frequency roll-off - 1 db f h 20 -- khz closed loop voltage gain g v 19 20 21 db supply voltage ripple rejection: note 7 on rr 48 -- db mute rr 48 -- db stand-by rr 80 -- db input impedance |z i |506075k w noise output voltage: note 8; on r s = 0 w v no(rms) - 50 -m v on r s = 10 k w v no(rms) - 70 100 m v mute note 9 v no(rms) - 50 -m v channel separation r s = 10 k wa 40 -- db channel balance g v -- 1db
july 1994 8 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ notes to the characteristics 1. all characteristics, for stereo application are measured using the circuit shown in fig.3. 2. the circuit is d.c. adjusted at v p = 6 v to 18 v and a.c. operating at v p = 8,5 to 18 v. 3. at 18 v < v p < 30 v the d.c. output voltage v p /2. 4. output power is measured directly at the output pins of the ic. 5. with bootstrap and a 100 k w resistor from pin 12 to the positive supply voltage (v p ), value of bootstrap capacitor is 47 m f. 6. frequency response externally fixed. 7. ripple rejection measured at the output with a source impedance of 0 w (maximum ripple amplitude of 2 v) and a frequency between 1 khz and 10 khz. 8. noise voltage measured in a bandwidth of 20 hz to 20 khz. 9. noise output voltage independent of r s (v i = 0 v). 10. all characteristics, for btl application are measured using the circuit shown in fig.4. btl application note 10 output power thd = 0,5% p o 15,5 17,0 - w thd = 10% p o 20 22 - w note 5; thd = 10% p o 21 24 - w output power at v p = 13,2 v thd = 0,5% p o - 13,5 - w thd = 10% p o - 17 - w note 5; thd = 10% p o - 19 - w power bandwidth thd = 0,5% p o = 15 w b w - 20 to - hz 15 000 low frequency roll-off note 6; - 3 db f l - 25 - hz high frequency roll-off - 1 db f h 20 -- khz closed loop voltage gain g v 25 26 27 db supply voltage ripple rejection: note 7 on rr 48 -- db mute rr 48 -- db stand-by rr 80 -- db input impedance |z i |253038k w noise output voltage note 8; on r s = 0 w v no(rms) - 70 -m v on r s = 10 k w v no(rms) - 100 200 m v mute note 9 v no(rms) - 60 -m v parameter conditions symbol min. typ. max. unit
july 1994 9 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ application information fig.3 stereo application circuit diagram. fig.4 btl application circuit diagram (without bootstrapping).
july 1994 10 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ package outline unit a e 1 a 2 b p cd (1) e (1) z (1) de d h ll 3 m references outline version european projection issue date iec jedec eiaj mm 17.0 15.5 4.6 4.2 0.75 0.60 0.48 0.38 24.0 23.6 20.0 19.6 10 3.4 v 0.8 12.2 11.8 1.7 e 2 5.08 2.4 1.6 e h 6 2.00 1.45 2.1 1.8 3.4 3.1 4.3 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. 12.4 11.0 sot141-6 0 5 10 mm scale q j 0.25 w 0.03 x d l e a c a 2 m l 3 q w m b p 1 d d z e 2 e e x h 113 j e h non-concave view b : mounting base side 92-11-17 95-03-11 dbs13p: plastic dil-bent-sil power package; 13 leads (lead length 12 mm) sot141-6 v m b
july 1994 11 philips semiconductors product speci?cation 24 w btl or 2 x 12 watt stereo car radio power ampli?er tda1516BQ soldering introduction there is no soldering method that is ideal for all ic packages. wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. however, wave soldering is not always suitable for surface mounted ics, or for printed-circuits with high population densities. in these situations reflow soldering is often used. this text gives a very brief insight to a complex technology. a more in-depth account of soldering ics can be found in our ic package databook (order code 9398 652 90011). soldering by dipping or by wave the maximum permissible temperature of the solder is 260 c; solder at this temperature must not be in contact with the joint for more than 5 seconds. the total contact time of successive solder waves must not exceed 5 seconds. the device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (t stg max ). if the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. repairing soldered joints apply a low voltage soldering iron (less than 24 v) to the lead(s) of the package, below the seating plane or not more than 2 mm above it. if the temperature of the soldering iron bit is less than 300 c it may remain in contact for up to 10 seconds. if the bit temperature is between 300 and 400 c, contact may be up to 5 seconds. definitions life support applications these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale. data sheet status objective speci?cation this data sheet contains target or goal speci?cations for product development. preliminary speci?cation this data sheet contains preliminary data; supplementary data may be published later. product speci?cation this data sheet contains ?nal product speci?cations. limiting values limiting values given are in accordance with the absolute maximum rating system (iec 134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information where application information is given, it is advisory and does not form part of the speci?cation.

▲Up To Search▲

Price & Availability of 1516BQ

	To Download 1516BQ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .